in your garage to make future searches easy.

Condition Value
expand_moreAxle drive
AWD clutch oil control screws 11.06 lbf⋅ft
Screws must be replaced.
Drive shaft heat protection plate 14.75 lbf⋅ft
expand_moreFront axle drive shaft
expand_moreAt the gearbox
M8 29.5 lbf⋅ft
Use new screws and tighten them crosswise.
M10 51.63 lbf⋅ft
Use new screws and tighten them crosswise.
expand_moreCentral screws
First stage 147.51 lbf⋅ft
Screws must be replaced.
Second stage 180°
Propeller shaft intermediate bearing 18.44 lbf⋅ft
expand_morePropeller shaft
At the gearbox 44.25 lbf⋅ft
expand_moreRear axle drive shaft
At the differential 29.5 lbf⋅ft
Use new screws and tighten them crosswise.
expand_moreCentral screws
First stage 147.51 lbf⋅ft
Screws must be replaced.
Second stage 180°
expand_moreTransfer case propeller shaft front axle
On transfer case 44.25 lbf⋅ft
Screws must be replaced.
expand_moreClutch
expand_moreClutch pressure plate
M6 9.59 lbf⋅ft
M7 14.75 lbf⋅ft
Clutch slave cylinder 14.75 lbf⋅ft
Clutch slave cylinder bleeder valve 3.32 lbf⋅ft
expand_moreDifferential
Rear axle differential oil control screws 11.06 lbf⋅ft
Screws must be replaced.
expand_moreGear shifting
Back-up lamp switch 14.75 lbf⋅ft
Sealing rings must be replaced.
Selector cable linkage 14.75 lbf⋅ft
expand_moreGearbox
expand_moreGearbox flange connection at engine
M10 29.5 lbf⋅ft
M12 59 lbf⋅ft
expand_moreOutput flange
At the gearbox 18.44 lbf⋅ft
expand_moreGearbox lubrication
Gearbox oil drain plug 22.13 lbf⋅ft
Sealing rings must be replaced.
expand_moreGearbox mounting
expand_moreGearbox mounting
expand_moreAt the gearbox
First stage 44.25 lbf⋅ft
Screws must be replaced.
Second stage 90°
expand_moreOn chassis
First stage 36.88 lbf⋅ft
Screws must be replaced.
Second stage 90°
expand_moreGearbox support
expand_moreAt the gearbox
expand_more0CW transmission
First stage 29.5 lbf⋅ft
Screws must be replaced.
Second stage 90°
expand_more0FB gearbox
First stage 44.25 lbf⋅ft
Screws must be replaced.
Second stage 90°
expand_more02Q gearbox
First stage 44.25 lbf⋅ft
Screws must be replaced.
Second stage 90°
expand_more0A4 gearbox
First stage 14.75 lbf⋅ft
Screws must be replaced.
Second stage 90°
expand_moreTransfer case
Bevel gear mounting 29.5 lbf⋅ft
Screw in screw manually up to stop.
expand_moreTransfer box onto transmission flange connection
First stage 29.5 lbf⋅ft
Screws must be replaced.
Second stage 90°

Please be noted that all capacities listed here are approximate. Check fluid levels when adding or refilling as recommended in your 2020 Volkswagen Golf AllTrack user's manual. Keep in mind that all information here is provided “as is” without any warranty of any kind.

Before doing any DIY service please check your insurance policy and Volkswagen warranty policy for your region. In some regions DIY service may invalidate your warranty.

Conquer your fears and never give up!

DIY car service is not as difficult as it looks like and it might save you thousands of dollars per year. It might be even fun and a good thing to do with your kids on a weekend to teach them how basic machinery works. It's really hard to screw something up and damage your car permanently if you use right tools, follow Volkswagen Golf AllTrack service manual and use right parts and fluids in prescribed amounts. Even modern cars stuffed with electronics can be serviced in your garage or even in your driveway. Changing engine oil, brake fluid, ATF, replacing brake pads, and etc. It's all may be done by yourself in a mater of a couple of hours.

Doing basic service for your 2020 Volkswagen Golf AllTrack you're not only saving money, but also also improving your technical skills and learning something new.

Units:
facebook twitter reddit linkedin messenger whatsapp telegram skype email chat