2006 Kia Ceed SW First generation Engine Fastener Tightening Specifications
in your garage to make future searches easy.
Condition | Value |
---|
Induction-pipe flap control unit | 7.38–8.85 lbf⋅ft |
Intake manifold | 14.75–18.44 lbf⋅ft |
Intake manifold support | 7.38 lbf⋅ft |
Air-conditioning compressor pressure line | 14.75–22.13 lbf⋅ft |
Code range 12 mm | 14.75–22.13 lbf⋅ft |
Code range 14 mm | 22.13–29.5 lbf⋅ft |
All other modifications | 33.19–40.57 lbf⋅ft |
All other modifications | 19.18–22.13 lbf⋅ft |
Generator bracket | 14.75–22.13 lbf⋅ft |
Vacuum pump | 8.85 lbf⋅ft |
Exhaust gas return cooler | 14.75 lbf⋅ft |
Exhaust gas return valve | 14.75–18.44 lbf⋅ft |
All other modifications | 11.06–14.75 lbf⋅ft |
High-pressure line | 18.44 lbf⋅ft |
High-pressure pump pulley | 47.94–55.32 lbf⋅ft |
Injection pump | 11.06–14.75 lbf⋅ft |
Turbocharger bracket | 25.08–29.5 lbf⋅ft |
At the turbocharger | 8.85–13.28 lbf⋅ft |
On the engine block | 13.28–17.7 lbf⋅ft |
At the turbocharger | 7.38–8.85 lbf⋅ft |
On the engine block | 10.33–14.75 lbf⋅ft |
All other modifications | 7.38–8.85 lbf⋅ft |
Seals must be replaced. |
All other modifications | 7.38–8.85 lbf⋅ft |
Tighten the screws crosswise. |
Fan wheel | 5.9–7.38 lbf⋅ft |
Radiator drain screws | 5.9–10.33 lbf⋅ft |
Radiator mounting | 5.9–7.38 lbf⋅ft |
M6 screws | 8.85–10.33 lbf⋅ft |
M8 screws | 16.23 lbf⋅ft |
First stage | 14.75 lbf⋅ft |
Screws must be replaced. | |
Second stage | 90° |
Third stage | 100° |
First stage | 22.13 lbf⋅ft |
Screws must be replaced. | |
Second stage | 90° |
Third stage | 90° |
Valve cover | 5.9–7.38 lbf⋅ft |
Seals must be replaced. |
Balance shaft module | 38.35–40.57 lbf⋅ft |
First stage | 14.75 lbf⋅ft |
Second stage | 90° |
All other modifications | 95.88–103.26 lbf⋅ft |
All other modifications | 55.32 lbf⋅ft |
Tighten cross-wise. |
All other modifications | 55.32 lbf⋅ft |
First stage | 14.75 lbf⋅ft |
Tighten the screws cross-wise from inside to outside. | |
Second stage | 90° |
Camshaft drive belt deflection pulley | 33.19–36.88 lbf⋅ft |
Camshaft timing chain guide rail | 7.38–8.85 lbf⋅ft |
Camshaft timing chain slip rail | 7.38–10.33 lbf⋅ft |
Camshaft timing chain tensioner | 7.38–8.85 lbf⋅ft |
Camshaft timing chain tensioning rail | 7.38–8.85 lbf⋅ft |
Chain tensioner | 7.38–8.85 lbf⋅ft |
Control drive chain guide rail | 7.38–8.85 lbf⋅ft |
Control drive chain tensioner | 7.38–8.85 lbf⋅ft |
Inlet camshaft wheel | 51.63–54.58 lbf⋅ft |
Outlet camshaft wheel | 51.63–54.58 lbf⋅ft |
Screws with thread length 10 mm | 7.38–8.85 lbf⋅ft |
Screws with thread length 12 mm | 14.75–18.44 lbf⋅ft |
Toothed belt guard | 5.9–8.85 lbf⋅ft |
Toothed belt tightener | 36.88–40.57 lbf⋅ft |
Oil drain plug | 25.08–32.45 lbf⋅ft |
Oil sump lower part | 7.38–8.85 lbf⋅ft |
Oil sump top part | 14.75–18.44 lbf⋅ft |
All other modifications | 14.75–18.44 lbf⋅ft |
All other modifications | 29.5–36.88 lbf⋅ft |
Subframe | 118.01–132.76 lbf⋅ft |
Subframe stiffening plate | 33.19–40.57 lbf⋅ft |
Front | 36.88–47.94 lbf⋅ft |
Rear | 36.88–47.94 lbf⋅ft |
At the subframe | 36.88–47.94 lbf⋅ft |
Catalytic converter | 29.5–36.88 lbf⋅ft |
Nuts must be replaced. | |
Diesel particulate filter | 29.5–44.25 lbf⋅ft |
Differential pressure sensor lines | 29.5–44.25 lbf⋅ft |
All other modifications | 22.13–25.81 lbf⋅ft |
Nuts must be replaced. |
Exhaust manifold heat shields | 11.8–14.75 lbf⋅ft |
Fuel filter bracket | 14.75–18.44 lbf⋅ft |
Fuel filter housing | 7.38–11.06 lbf⋅ft |
Fuel lines | 14.75–18.44 lbf⋅ft |
Fuel pump | 2.95–4.43 lbf⋅ft |
Spark plugs | 14.75–22.13 lbf⋅ft |
All other modifications | 33.19–40.57 lbf⋅ft |
Please be noted that all capacities listed here are approximate. Check fluid levels when adding or refilling as recommended in your 2006 Kia Ceed SW user's manual. Keep in mind that all information here is provided “as is” without any warranty of any kind.
Before doing any DIY service please check your insurance policy and Kia warranty policy for your region. In some regions DIY service may invalidate your warranty.
Table of Contents
- Air Conditioning Compressor Oil Capacity
- Air Conditioning Refrigerant Capacity
- Automatic Transmission Fluid Capacity
- Brake Fluid Capacity
- Clutch Fluid Capacity
- Cooling Fluid Capacity
- Engine Oil Capacity
- Fluid and Lubricant Specifications
- Manual Transmission Oil Capacity
- Brake System Specifications
- Chassis Specifications
- Cooling System Specifications
- Electrical System Specifications
- Emission
Conquer your fears and never give up!
DIY car service is not as difficult as it looks like and it might save you thousands of dollars per year. It might be even fun and a good thing to do with your kids on a weekend to teach them how basic machinery works. It's really hard to screw something up and damage your car permanently if you use right tools, follow Kia Ceed SW service manual and use right parts and fluids in prescribed amounts. Even modern cars stuffed with electronics can be serviced in your garage or even in your driveway. Changing engine oil, brake fluid, ATF, replacing brake pads, and etc. It's all may be done by yourself in a mater of a couple of hours.
Doing basic service for your 2006 Kia Ceed SW you're not only saving money, but also also improving your technical skills and learning something new.