2015 Audi Q3 RS First generation Front Suspension Fastener Tightening Specifications
in your garage to make future searches easy.
| Condition | Value |
|---|
| Bleed valve | 9.59 lbf⋅ft |
| At the brake caliper | 11.06 lbf⋅ft |
| Socket unions | 10.33 lbf⋅ft |
| On stub axle | 147.51 lbf⋅ft |
| Replace screws. | |
| RS 2.5 quattro with gasoline straight-5 2.5 L 335 HP at 5300 RPM, 450 N⋅m at 1600 RPM engine (2013.5–) | 147.51 lbf⋅ft |
| Replace screws. | |
| Front axle brake disc | 2.95 lbf⋅ft |
| Wheel speed sensor | 5.9 lbf⋅ft |
| Lower steering column joint | 22.13 lbf⋅ft |
| Replace screws. | |
| Steering column | 14.75 lbf⋅ft |
| First stage | 36.88 lbf⋅ft |
| Replace screws. | |
| Second stage | 90° |
| Steering wheel | 36.88 lbf⋅ft |
| Replace nuts. | |
| Track rod end on stub axle | 36.88 lbf⋅ft |
| Replace nuts. | |
| Track rod end on track rod | 51.63 lbf⋅ft |
| Track rod on steering gear | 73.76 lbf⋅ft |
| Shock-absorber piston rod | 44.25 lbf⋅ft |
| Replace nuts. | |
| First stage | 11.06 lbf⋅ft |
| Replace screws. | |
| Second stage | 90° |
| First stage | 51.63 lbf⋅ft |
| Replace screws. | |
| Second stage | 90° |
| First stage | 7.38 lbf⋅ft |
| Use new screws and tighten them crosswise. | |
| Second stage | 51.63 lbf⋅ft |
| Second stage | 29.5 lbf⋅ft |
| First stage | 147.51 lbf⋅ft |
| Replace screws. | |
| Second stage | 180° |
| Stabiliser mounting at the stabiliser | 47.94 lbf⋅ft |
| Replace nuts. | |
| Stabiliser mounting at suspension strut | 47.94 lbf⋅ft |
| Replace nuts. | |
| First stage | 14.75 lbf⋅ft |
| Replace screws. | |
| Second stage | 90° |
| Support joint at the stub axle | 44.25 lbf⋅ft |
| Replace nuts. | |
| Support joint at the transverse control arm | 73.76 lbf⋅ft |
| Replace nuts. | |
| First stage | 36.88 lbf⋅ft |
| Replace screws. | |
| Second stage | 90° |
| First stage | 51.63 lbf⋅ft |
| Replace screws. | |
| Second stage | 180° |
| First stage | 51.63 lbf⋅ft |
| Replace screws. | |
| Second stage | 180° |
| First stage | 51.63 lbf⋅ft |
| Replace screws. | |
| Second stage | 90° |
| Tire pressure sensors | 2.95 lbf⋅ft |
| Replace bolts. | |
| Wheel attachment | 103.26 lbf⋅ft |
Please be noted that all capacities listed here are approximate. Check fluid levels when adding or refilling as recommended in your 2015 Audi Q3 RS user's manual. Keep in mind that all information here is provided “as is” without any warranty of any kind.
Before doing any DIY service please check your insurance policy and Audi warranty policy for your region. In some regions DIY service may invalidate your warranty.
Table of Contents
- Air Conditioning Compressor Oil Capacity
- Air Conditioning Refrigerant Capacity
- All-wheel Drive Clutch Oil Capacity
- Axle Oil Capacity
- Brake Fluid Capacity
- Cooling Fluid Capacity
- Engine Oil Capacity
- Fluid and Lubricant Specifications
- Gearbox Oil Capacity
- Manual Transmission Oil Capacity
- Brake System Specifications
- Chassis Specifications
- Cooling System Specifications
- Electrical System Specifications
- Emission
- Engine Fastener Tightening Specifications
- Front Suspension Fastener Tightening Specifications
- Rear Suspension Fastener Tightening Specifications
- Transmission Fastener Tightening Specifications
Conquer your fears and never give up!
DIY car service is not as difficult as it looks like and it might save you thousands of dollars per year. It might be even fun and a good thing to do with your kids on a weekend to teach them how basic machinery works. It's really hard to screw something up and damage your car permanently if you use right tools, follow Audi Q3 RS service manual and use right parts and fluids in prescribed amounts. Even modern cars stuffed with electronics can be serviced in your garage or even in your driveway. Changing engine oil, brake fluid, ATF, replacing brake pads, and etc. It's all may be done by yourself in a mater of a couple of hours.
Doing basic service for your 2015 Audi Q3 RS you're not only saving money, but also also improving your technical skills and learning something new.