2013 Audi A5 Cabriolet First generation facelift Engine Fastener Tightening Specifications
in your garage to make future searches easy.
Condition | Value |
---|
First stage | 2.21 lbf⋅ft |
Second stage | 7.38 lbf⋅ft |
All Audi diesel straight-4 2.0 L CAHA engines | 5.9 lbf⋅ft |
All Audi diesel straight-4 2.0 L CAHB engines | 5.9 lbf⋅ft |
Lower section of intake manifold | 6.64 lbf⋅ft |
Upper section of intake manifold | 5.9 lbf⋅ft |
Lower section of intake manifold | 6.64 lbf⋅ft |
tighten gradually cross-wise | |
Upper section of intake manifold | 6.64 lbf⋅ft |
All Audi diesel straight-4 2.0 L CGLC engines | 2.95 lbf⋅ft |
All Audi diesel straight-4 2.0 L CGLD engines | 5.9 lbf⋅ft |
All Audi diesel straight-4 2.0 L CJCA engines | 5.9 lbf⋅ft |
All Audi diesel straight-4 2.0 L CJCD engines | 5.9 lbf⋅ft |
First stage | Screw in new screw(s) manually as far as it goes. |
Second stage | 14.75 lbf⋅ft |
Third stage | 90° |
All other modifications | 6.64 lbf⋅ft |
Nuts | 7.38 lbf⋅ft |
Screws | 14.75 lbf⋅ft |
First stage | Screw in screw manually up to stop. |
Second stage | 14.75 lbf⋅ft |
First stage | 14.75 lbf⋅ft |
Second stage | 90° |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
All Audi gasoline V6 3.2 L CALA engines | 29.5 lbf⋅ft |
All Audi diesel V6 2.7 L CGKA engines | 16.96 lbf⋅ft |
All Audi diesel V6 2.7 L CGKB engines | 16.96 lbf⋅ft |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 14.75 lbf⋅ft |
Use new screw. | |
Second stage | 90° |
First stage | 14.75 lbf⋅ft |
Use new screw. | |
Second stage | 90° |
All Audi diesel V6 3.0 L CLAB engines | 16.96 lbf⋅ft |
All other modifications | 14.75 lbf⋅ft |
First stage | 5.9 lbf⋅ft |
Second stage | 45° |
First stage | 5.9 lbf⋅ft |
Replace screws. | |
Second stage | 45° |
All Audi diesel straight-4 2.0 L CAHA engines | 16.96 lbf⋅ft |
First stage | 14.75 lbf⋅ft |
Second stage | 180° |
First stage | 36.88 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
M8 | 16.96 lbf⋅ft |
First stage | 14.75 lbf⋅ft |
Second stage | 180° |
First stage | 14.75 lbf⋅ft |
Second stage | 180° |
First stage | 36.88 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 14.75 lbf⋅ft |
Second stage | 90° |
All other modifications | 29.5 lbf⋅ft |
First stage | 5.9 lbf⋅ft |
Replace screws. | |
Second stage | 180° |
Steel screws | 18.44 lbf⋅ft |
All Audi diesel straight-4 2.0 L CJCA engines | 16.96 lbf⋅ft |
First stage | 5.9 lbf⋅ft |
Second stage | 180° |
Steel screws | 18.44 lbf⋅ft |
All other modifications | 18.44 lbf⋅ft |
First stage | Tighten bolt(s) until hand-tight. |
Replace screws. | |
Second stage | 14.75 lbf⋅ft |
Third stage | 90° |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 180° |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 60° |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 60° |
All Audi gasoline V6 3.2 L CALA engines | 14.75 lbf⋅ft |
All Audi diesel V6 2.7 L CGKA engines | 29.5 lbf⋅ft |
All Audi diesel V6 2.7 L CGKB engines | 29.5 lbf⋅ft |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 180° |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 60° |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 60° |
First stage | Tighten by hand |
Replace screws. | |
Second stage | 29.5 lbf⋅ft |
Third stage | 180° |
First stage | Tighten by hand |
Replace screws. | |
Second stage | 29.5 lbf⋅ft |
Third stage | 60° |
First stage | Tighten by hand |
Replace screws. | |
Second stage | 29.5 lbf⋅ft |
Third stage | 60° |
All Audi diesel V6 3.0 L CLAB engines | 29.5 lbf⋅ft |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
M6 | 6.64 lbf⋅ft |
M8 | 18.44 lbf⋅ft |
First stage | 5.9 lbf⋅ft |
Use new screws. | |
Second stage | 180° |
Steel screws | 16.96 lbf⋅ft |
All other modifications | 16.96 lbf⋅ft |
First stage | Tighten bolt(s) until hand-tight. |
Replace screws. | |
Second stage | 14.75 lbf⋅ft |
Third stage | 90° |
First stage | 29.5 lbf⋅ft |
Second stage | 180° |
First stage | 29.5 lbf⋅ft |
Second stage | 45° |
First stage | 29.5 lbf⋅ft |
Second stage | 90° |
First stage | 29.5 lbf⋅ft |
Second stage | 90° |
First stage | 29.5 lbf⋅ft |
Second stage | 90° |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 180° |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 60° |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 60° |
First stage | 14.75 lbf⋅ft |
Tighten cross-wise. | |
Second stage | 90° |
All Audi diesel V6 2.7 L CGKA engines | 29.5 lbf⋅ft |
All Audi diesel V6 2.7 L CGKB engines | 29.5 lbf⋅ft |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 180° |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 60° |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 60° |
First stage | Tighten by hand |
Replace screws. | |
Second stage | 29.5 lbf⋅ft |
Third stage | 180° |
First stage | Tighten by hand |
Replace screws. | |
Second stage | 29.5 lbf⋅ft |
Third stage | 60° |
First stage | Tighten by hand |
Replace screws. | |
Second stage | 29.5 lbf⋅ft |
Third stage | 60° |
All Audi diesel V6 3.0 L CLAB engines | 29.5 lbf⋅ft |
First stage | Screw in screw manually up to stop. |
Second stage | 29.5 lbf⋅ft |
Third stage | 45° |
Fourth stage | 180° |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
All Audi gasoline V6 3.2 L CALA engines | 14.75 lbf⋅ft |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
M6 | 6.64 lbf⋅ft |
Union nuts | 28.03 lbf⋅ft |
Servo pump pulley | 16.23 lbf⋅ft |
All Audi gasoline V6 3.2 L CALA engines | 14.75 lbf⋅ft |
All other modifications | 18.44 lbf⋅ft |
All Audi diesel straight-4 2.0 L CJCA engines | 7.38 lbf⋅ft |
All other modifications | 6.64 lbf⋅ft |
First stage | Screw in screw manually up to stop. |
Use new seals. | |
Second stage | 14.75 lbf⋅ft |
2.0 TDI with diesel straight-4 2.0 L 188 HP engine (2013.9–) | 14.75 lbf⋅ft |
All Audi gasoline straight-4 1.8 L CABD engines | 6.64 lbf⋅ft |
All Audi gasoline straight-4 2.0 L CAED engines | 3.69 lbf⋅ft |
All Audi gasoline V6 3.2 L CALA engines | 6.64 lbf⋅ft |
All Audi gasoline straight-4 1.8 L CJEB engines | 6.64 lbf⋅ft |
All Audi gasoline straight-4 2.0 L CNCD engines | 6.64 lbf⋅ft |
All Audi diesel straight-4 2.0 L CNHA engines | 14.75 lbf⋅ft |
All other modifications | 16.23 lbf⋅ft |
Union nuts | 19.91 lbf⋅ft |
All Audi gasoline straight-4 2.0 L CAED engines | 19.91 lbf⋅ft |
All Audi gasoline V6 3.2 L CALA engines | 19.91 lbf⋅ft |
Union nuts | 14.75 lbf⋅ft |
All Audi diesel straight-4 2.0 L CNHA engines | 20.65 lbf⋅ft |
All other modifications | 18.44 lbf⋅ft |
Check compressed air line. |
First stage | 5.9 lbf⋅ft |
Second stage | 90° |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 180° |
All Audi gasoline V6 3.2 L CALA engines | 6.64 lbf⋅ft |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 45° |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 180° |
Nuts | 70.07 lbf⋅ft |
Screws | 14.75 lbf⋅ft |
Replace screws. |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 45° |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 180° |
All Audi diesel V6 3.0 L CLAB engines | 16.23 lbf⋅ft |
First stage | 14.75 lbf⋅ft |
Short screws | 45° |
Long screws | 180° |
All other modifications | 14.75 lbf⋅ft |
Tighten bolts uniformly in several passes. |
Central nuts | 51.63 lbf⋅ft |
Central nuts | 70.07 lbf⋅ft |
Screws | 14.75 lbf⋅ft |
Replace screws. |
Central nuts | 70.07 lbf⋅ft |
Wheel | 14.75 lbf⋅ft |
Replace bolts. |
Central nuts | 70.07 lbf⋅ft |
Wheel | 14.75 lbf⋅ft |
Replace bolts. |
Central nuts | 51.63 lbf⋅ft |
All Audi diesel straight-4 2.0 L CNHA engines | 70.07 lbf⋅ft |
Central nuts | 70.07 lbf⋅ft |
Wheel | 14.75 lbf⋅ft |
Replace screws. |
All Audi gasoline V6 3.2 L CALA engines | 19.91 lbf⋅ft |
All other modifications | 18.44 lbf⋅ft |
Check compressed air line. |
Nuts | 7.38 lbf⋅ft |
Screws | 3.69 lbf⋅ft |
Nuts | 7.38 lbf⋅ft |
Screws | 3.69 lbf⋅ft |
First stage | 5.9 lbf⋅ft |
Replace screws. | |
Second stage | 180° |
Retaining clamp | 10.33 lbf⋅ft |
First stage | 1.48 lbf⋅ft |
Use new screws. | |
Second stage | 6.64 lbf⋅ft |
Third stage | 180° |
First stage | 5.9 lbf⋅ft |
Replace screws. | |
Second stage | 180° |
All Audi diesel straight-4 2.0 L CAHA engines | 14.75 lbf⋅ft |
High-pressure pump | 7.38 lbf⋅ft |
Replace screws. |
M6 | 6.64 lbf⋅ft |
M8 | 16.96 lbf⋅ft |
High-pressure pump | 14.75 lbf⋅ft |
All Audi gasoline straight-4 1.8 L CDHB engines | 18.44 lbf⋅ft |
On high-pressure pump | 29.5 lbf⋅ft |
Replace components. | |
On rail | 29.5 lbf⋅ft |
Replace components. |
All other modifications | 29.5 lbf⋅ft |
Replace components. |
All Audi diesel V6 2.7 L CGKA engines | 6.64 lbf⋅ft |
All Audi diesel V6 2.7 L CGKB engines | 6.64 lbf⋅ft |
All Audi diesel straight-4 2.0 L CNHA engines | 5.9 lbf⋅ft |
First stage | 22.13 lbf⋅ft |
Replace bolts. Use mounting lubricant. | |
Second stage | 90° |
All Audi diesel straight-4 2.0 L CGLC engines | 17.7 lbf⋅ft |
Replace nuts. | |
All Audi diesel straight-4 2.0 L CJCD engines | 17.7 lbf⋅ft |
Replace nuts. Use hot screw paste. | |
All other modifications | 18.44 lbf⋅ft |
Replace the nuts and use fitting paste |
All Audi gasoline straight-4 2.0 L CAED engines | 22.13 lbf⋅ft |
M10 | 29.5 lbf⋅ft |
M8 | 14.75 lbf⋅ft |
All Audi gasoline straight-4 2.0 L CNCD engines | 22.13 lbf⋅ft |
First stage | Screw in new screw(s) manually as far as it goes. |
Second stage | 14.75 lbf⋅ft |
Banjo screws | 25.81 lbf⋅ft |
Replace sealing rings. |
All Audi gasoline straight-4 2.0 L CNCD engines | 6.64 lbf⋅ft |
Banjo screws | 25.81 lbf⋅ft |
Replace sealing rings. |
All Audi gasoline straight-4 2.0 L CNCD engines | 6.64 lbf⋅ft |
Banjo screws | 22.13 lbf⋅ft |
Replace sealing rings. | |
Screws | 6.64 lbf⋅ft |
Replace sealing rings. |
Banjo screws | 22.13 lbf⋅ft |
Replace sealing rings. | |
Union nuts | 16.23 lbf⋅ft |
All Audi gasoline straight-4 2.0 L CNCD engines | 6.64 lbf⋅ft |
At the turbocharger | 16.23 lbf⋅ft |
On the engine block | 22.13 lbf⋅ft |
All Audi gasoline straight-4 2.0 L CAED engines | 6.64 lbf⋅ft |
Replace sealing rings. | |
All Audi diesel straight-4 2.0 L CJCD engines | 6.64 lbf⋅ft |
M6 | 6.64 lbf⋅ft |
M8 | 18.44 lbf⋅ft |
At the turbocharger | 10.33 lbf⋅ft |
On the engine block | 7.38 lbf⋅ft |
All Audi diesel straight-4 2.0 L CAHA engines | 11.06 lbf⋅ft |
All Audi diesel straight-4 2.0 L CAHB engines | 11.06 lbf⋅ft |
All Audi diesel straight-4 2.0 L CGLC engines | 11.06 lbf⋅ft |
All Audi diesel straight-4 2.0 L CGLD engines | 11.06 lbf⋅ft |
All Audi diesel straight-4 2.0 L CJCA engines | 11.06 lbf⋅ft |
All Audi diesel straight-4 2.0 L CJCD engines | 11.06 lbf⋅ft |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 45° |
All other modifications | 6.64 lbf⋅ft |
Gradually tighten screws crosswise. |
All Audi gasoline V6 3.2 L CALA engines | 14.75 lbf⋅ft |
All Audi diesel V6 2.7 L CGKA engines | 16.96 lbf⋅ft |
All Audi diesel V6 2.7 L CGKB engines | 16.96 lbf⋅ft |
All Audi diesel V6 3.0 L CLAB engines | 16.96 lbf⋅ft |
First stage | 7.38 lbf⋅ft |
Use new screw. (left-hand thread) | |
Second stage | 90° |
All Audi gasoline straight-4 2.0 L CAED engines | 2.21 lbf⋅ft |
All Audi diesel straight-4 2.0 L CJCD engines | 2.95 lbf⋅ft |
All Audi gasoline straight-4 2.0 L CNCD engines | 2.21 lbf⋅ft |
All other modifications | 3.69 lbf⋅ft |
Radiator mounting | 2.58 lbf⋅ft |
First stage | 5.9 lbf⋅ft |
Tighten new screws in inside-to-outside order. | |
Second stage | 90° |
First stage | Tighten bolt(s) until hand-tight. |
Replace screws. | |
Second stage | 5.9 lbf⋅ft |
Third stage | 90° |
First stage | Screw in screw(s) by hand. |
Replace screws. |
First step | 5.9 lbf⋅ft |
Second step | 90° |
First stage | 5.9 lbf⋅ft |
Tighten from inside to outside. | |
Second stage | 90° |
First stage | Tighten bolt(s) until hand-tight. |
Note correct order of tensioning. | |
Second stage | 7.38 lbf⋅ft |
First stage | Screw in screw(s) by hand. |
Note correct order of tensioning. | |
Second stage | 6.64 lbf⋅ft |
First stage | Tighten bolt(s) until hand-tight. |
Second stage | 5.9 lbf⋅ft |
All other modifications | 7.38 lbf⋅ft |
Tighten gradually and alternately from inside to outside. |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Third stage | 90° |
First step | 5.9 lbf⋅ft |
Replace screws. | |
Second step | 90° |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Third stage | 90° |
Fourth stage | 5.9 lbf⋅ft |
Replace screws. | |
Fifth stage | 90° |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 44.25 lbf⋅ft |
Third stage | 90° |
Fourth stage | 90° |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Third stage | 90° |
Fourth stage | 29.5 lbf⋅ft |
Replace screws. | |
Fifth stage | 90° |
Sixth stage | 90° |
Seventh stage | 6.64 lbf⋅ft |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Third stage | 90° |
First step | 5.9 lbf⋅ft |
Replace screws. | |
Second step | 90° |
First stage | 25.81 lbf⋅ft |
Use new screws | |
Second stage | 44.25 lbf⋅ft |
Third stage | 90° |
Fourth stage | 90° |
First stage | 22.13 lbf⋅ft |
Replace screws. | |
Second stage | 36.88 lbf⋅ft |
Third stage | 90° |
Fourth stage | 90° |
First stage | 29.5 lbf⋅ft |
Use new screws. | |
Second stage | 44.25 lbf⋅ft |
Third stage | 90° |
Fourth stage | 90° |
First stage | 22.13 lbf⋅ft |
Replace screws. | |
Second stage | 36.88 lbf⋅ft |
Third stage | 90° |
Fourth stage | 90° |
First stage | Tighten by hand |
Replace screws. | |
Second stage | 25.81 lbf⋅ft |
Third stage | 51.63 lbf⋅ft |
Fourth stage | 90° |
Fifth stage | 90° |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Third stage | 90° |
Fourth stage | 2.95 lbf⋅ft |
Replace screws. | |
Fifth stage | 90° |
First stage | 22.13 lbf⋅ft |
Replace screws. | |
Second stage | 47.94 lbf⋅ft |
Third stage | 90° |
Fourth stage | 90° |
First stage | 29.5 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Third stage | 90° |
First step | 5.9 lbf⋅ft |
Replace screws. | |
Second step | 90° |
Fifth stage | 29.5 lbf⋅ft |
Replace screws. | |
Sixth stage | 90° |
Seventh stage | 90° |
All Audi diesel V6 2.7 L CGKA engines | 6.26 in |
All Audi diesel V6 2.7 L CGKB engines | 6.26 in |
All other modifications | 5.39 in |
First stage | 5.9 lbf⋅ft |
Tighten new screws in inside-to-outside order. | |
Second stage | 90° |
First stage | Tighten by hand |
Tighten cross-wise. | |
Second stage | 7.38 lbf⋅ft |
All Audi gasoline V6 3.2 L CALA engines | 6.64 lbf⋅ft |
All Audi diesel V6 2.7 L CGKA engines | 6.64 lbf⋅ft |
Tighten cross-wise. | |
All Audi diesel V6 2.7 L CGKB engines | 6.64 lbf⋅ft |
Tighten cross-wise. |
First stage | Tighten by hand |
Tighten cross-wise. | |
Second stage | 6.64 lbf⋅ft |
First stage | Tighten by hand |
Gradually tighten screws crosswise. | |
Second stage | 7.38 lbf⋅ft |
CJCA engine | 6.64 lbf⋅ft |
Tighten gradually and alternately from inside to outside. |
All Audi diesel straight-4 2.0 L CJCD engines | 6.64 lbf⋅ft |
Tighten the screws crosswise. |
First stage | Screw in screw(s) by hand. |
Replace screws. |
First step | 5.9 lbf⋅ft |
Second step | 90° |
All Audi diesel straight-4 2.0 L CNHA engines | 6.64 lbf⋅ft |
Tighten the screws cross-wise from inside to outside. |
First stage | 5.9 lbf⋅ft |
Tighten new screws in inside-to-outside order. | |
Second stage | 90° |
Valve cover locking screws | 3.69 lbf⋅ft |
First stage | 7.38 lbf⋅ft |
Use new screw. (left-hand thread) | |
Second stage | 90° |
Bearing casing | 6.64 lbf⋅ft |
Replace screws. |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Central screws | 44.25 lbf⋅ft |
First stage | 11.06 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
All Audi diesel V6 2.7 L CGKA engines | 16.96 lbf⋅ft |
All Audi diesel V6 2.7 L CGKB engines | 16.96 lbf⋅ft |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Central screws | 44.25 lbf⋅ft |
First stage | 22.13 lbf⋅ft |
Shaft must be replaced when the screw connection has been loosened. | |
Second stage | 90° |
Wheel | 16.96 lbf⋅ft |
First stage | 2.95 lbf⋅ft |
Replace screws. | |
Second stage | 45° |
First stage | 7.38 lbf⋅ft |
Use new screw. (left-hand thread) | |
Second stage | 90° |
On the engine block | 6.64 lbf⋅ft |
First stage | Screw in screw(s) finger tight. |
Replace screws. | |
Second stage | 4.43 lbf⋅ft |
Fifth stage | 90° |
Third stage | 14.75 lbf⋅ft |
Fourth stage | 9.59 lbf⋅ft |
First stage | 33.19 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 33.19 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 25.81 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 22.13 lbf⋅ft |
Use new screws. | |
Second stage | 90° |
First stage | 25.81 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 22.13 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Oil screw head support and thread. |
First stage | 22.13 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
2.0 TFSI with gasoline straight-4 2.0 L 221 HP at 4500 RPM, 350 N⋅m at 1500 RPM engine (2013.5–) | 6.64 lbf⋅ft |
Tighten screws crosswise. |
First stage | 132.76 lbf⋅ft |
Use new screw. | |
Second stage | 90° |
Third stage | 45° |
First stage | 132.76 lbf⋅ft |
Use new screw. | |
Second stage | 90° |
Third stage | 45° |
First stage | 132.76 lbf⋅ft |
Use new screws. | |
Second stage | 90° |
Third stage | 45° |
First stage | 132.76 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Oil screw head support and thread. | |
Third stage | 45° |
First stage | 110.63 lbf⋅ft |
Replace screws and oil sealing rings. | |
Second stage | 90° |
First stage | 7.38 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 44.25 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
3.0 TDI with diesel V6 3.0 L 201 HP at 3750 RPM, 400 N⋅m at 1250 RPM engine (2011.10–) | 18.44 lbf⋅ft |
All Audi gasoline straight-4 2.0 L CAED engines | 44.25 lbf⋅ft |
Replace screws. |
First stage | 44.25 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
To drive plate | 44.25 lbf⋅ft |
Replace screws. |
First stage | Tighten by hand |
Replace screws. |
First step | 47.94 lbf⋅ft |
Second step | 90° |
First step | 14.75 lbf⋅ft |
Second step | 90° |
First stage | Screw in screw(s) by hand. |
Replace screws. |
Second stage | 47.94 lbf⋅ft |
Third stage | 90° |
Fourth stage | 14.75 lbf⋅ft |
Fifth stage | 90° |
First stage | 47.94 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 4.43 lbf⋅ft |
Replace screws. |
First step | 9.59 lbf⋅ft |
Second step | 90° |
First step | 14.75 lbf⋅ft |
Second step | 90° |
First stage | 47.94 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 36.88 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Screws 17 – 31 | 16.96 lbf⋅ft |
First stage | Tighten by hand |
Tighten from inside to outside. | |
Second stage | 47.94 lbf⋅ft |
Replace screws. | |
Third stage | 90° |
Fourth stage | 14.75 lbf⋅ft |
Fifth stage | 90° |
First stage | 22.13 lbf⋅ft |
first tighten crosswise inside, then outside | |
Second stage | 36.88 lbf⋅ft |
Replace screws. | |
Third stage | 90° |
First stage | Screw in screw(s) by hand. |
Replace screws. | |
Second stage | 4.43 lbf⋅ft |
Fifth stage | 90° |
Third stage | 9.59 lbf⋅ft |
Fourth stage | 14.75 lbf⋅ft |
First stage | 47.94 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 4.43 lbf⋅ft |
Replace screws. |
First step | 9.59 lbf⋅ft |
Second step | 90° |
First step | 14.75 lbf⋅ft |
Second step | 90° |
First stage | 47.94 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 47.94 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 22.13 lbf⋅ft |
Replace screws. |
First step | 36.88 lbf⋅ft |
Second step | 180° |
All Audi diesel straight-4 2.0 L CNHA engines | Component must not be knocked down. |
First stage | 47.94 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 7.38 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Balance shaft timing chain guide rail | 14.75 lbf⋅ft |
Balance shaft timing chain tension rail | 14.75 lbf⋅ft |
First stage | 5.9 lbf⋅ft |
Replace screws. | |
Second stage | 45° |
First stage | 2.95 lbf⋅ft |
Replace screws. | |
Second stage | 45° |
First stage | 3.69 lbf⋅ft |
Tighten cross-wise. |
Second stage | 6.64 lbf⋅ft |
Third stage | 16.96 lbf⋅ft |
First stage | 5.9 lbf⋅ft |
Replace screws. | |
Second stage | 45° |
First stage | 5.9 lbf⋅ft |
Use new screws and tighten them crosswise. | |
Second stage | 45° |
First stage | 2.95 lbf⋅ft |
Replace screws. | |
Second stage | 180° |
Cap | 6.64 lbf⋅ft |
Central screws | 25.81 lbf⋅ft |
Left-hand thread |
Central screws | 25.81 lbf⋅ft |
Left-hand thread |
Bearing casing | 6.64 lbf⋅ft |
Camshaft adjuster valve | 6.64 lbf⋅ft |
Central screws | 25.81 lbf⋅ft |
Use new screw. (left-hand thread) |
First stage | 14.75 lbf⋅ft |
Use new screw. | |
Second stage | 90° |
Bearing casing | 6.64 lbf⋅ft |
Cap | 6.64 lbf⋅ft |
Central screws | 25.81 lbf⋅ft |
Left-hand thread |
First stage | 5.9 lbf⋅ft |
Use new screw. | |
Second stage | 90° |
First stage | 2.95 lbf⋅ft |
Replace screws. | |
Second stage | 180° |
First stage | 2.95 lbf⋅ft |
Replace screws. | |
Second stage | 45° |
Central screws | 25.81 lbf⋅ft |
Left-hand thread |
Bearing casing | 6.64 lbf⋅ft |
Cap | 6.64 lbf⋅ft |
Central screws | 25.81 lbf⋅ft |
Left-hand thread |
First stage | 36.88 lbf⋅ft |
Use new screw. | |
Second stage | 90° |
M8 | 14.75 lbf⋅ft |
First stage | 36.88 lbf⋅ft |
Use new screw. | |
Second stage | 90° |
M8 | 14.75 lbf⋅ft |
Screws | 14.75 lbf⋅ft |
Replace bolt. | |
Stud screws | 11.06 lbf⋅ft |
Replace the stud bolt. | |
Otherwise | 14.75 lbf⋅ft |
Replace nuts. |
First stage | 36.88 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
M8 | 14.75 lbf⋅ft |
Camshaft timing chain guide rail | 14.75 lbf⋅ft |
First stage | 3.69 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 3.69 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
All other modifications | 14.75 lbf⋅ft |
First stage | 3.69 lbf⋅ft |
Use new screw. | |
Second stage | 90° |
First stage | 3.69 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 2.95 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
All other modifications | 6.64 lbf⋅ft |
First stage | 3.69 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
All other modifications | 14.75 lbf⋅ft |
Central screws | 55.32 lbf⋅ft |
Otherwise | 16.96 lbf⋅ft |
Central screws | 73.76 lbf⋅ft |
Wheel | 18.44 lbf⋅ft |
All Audi diesel straight-4 2.0 L CJCA engines | 18.44 lbf⋅ft |
Central screws | 73.76 lbf⋅ft |
Wheel | 18.44 lbf⋅ft |
Replace screws. Use screw-locking compound. |
All Audi diesel V6 3.0 L CLAB engines | 16.96 lbf⋅ft |
Central screws | 73.76 lbf⋅ft |
Clamping screws | 6.64 lbf⋅ft |
Central screws | 73.76 lbf⋅ft |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 45° |
All Audi gasoline V6 3.2 L CALA engines | 6.64 lbf⋅ft |
All Audi diesel V6 2.7 L CGKA engines | 8.85 lbf⋅ft |
All Audi diesel V6 2.7 L CGKB engines | 8.85 lbf⋅ft |
First stage | 3.69 lbf⋅ft |
Use new screw. | |
Second stage | 90° |
All other modifications | 47.94 lbf⋅ft |
Screw with bearing bush | 8.85 lbf⋅ft |
Use screw-locking compound. |
All Audi diesel V6 3.0 L CLAB engines | 16.96 lbf⋅ft |
All other modifications | 14.75 lbf⋅ft |
First stage | 5.9 lbf⋅ft |
Replace screws. | |
Second stage | 45° |
First stage | 22.13 lbf⋅ft |
Use new screw. | |
Second stage | 90° |
First stage | 4.43 lbf⋅ft |
Use new screw. | |
Second stage | 60° |
Left | 33.19 lbf⋅ft |
First stage | 3.69 lbf⋅ft |
Use new screw. | |
Second stage | 90° |
First stage | 7.38 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Bottom | 8.85 lbf⋅ft |
First stage | 3.69 lbf⋅ft |
Second stage | 90° |
Bottom | 8.85 lbf⋅ft |
First stage | 3.69 lbf⋅ft |
Second stage | 90° |
First stage | 3.69 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
All other modifications | 14.75 lbf⋅ft |
2.0 TFSI with gasoline straight-4 2.0 L 221 HP at 4500 RPM, 350 N⋅m at 1500 RPM engine (2013.5–) | 3.69 lbf⋅ft |
First stage | 7.38 lbf⋅ft |
Replace screws. | |
Second stage | 45° |
All other modifications | 62.69 lbf⋅ft |
Use screw-locking compound. |
Injection pump drive belt tensioning roller | 16.96 lbf⋅ft |
First stage | 59 lbf⋅ft |
Use new screw. | |
Second stage | 90° |
First stage | 7.38 lbf⋅ft |
Replace screw and intermediate wheel when loosening the screw. | |
Second stage | for freedom from play |
First step | 18.44 lbf⋅ft |
Second step | 90° |
First stage | 7.38 lbf⋅ft |
Replace screw and intermediate wheel when loosening the screw. | |
Second stage | for freedom from play |
Third stage | 18.44 lbf⋅ft |
Fourth stage | 90° |
First stage | 66.38 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 66.38 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 66.38 lbf⋅ft |
Replace the screws and sprocket wheel. | |
Second stage | 90° |
First stage | 7.38 lbf⋅ft |
Replace the screws and sprocket wheel. | |
Second stage | for freedom from play |
First step | 18.44 lbf⋅ft |
Second step | 90° |
First stage | 7.38 lbf⋅ft |
Replace screws. | |
Second stage | 45° |
First stage | 3.69 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
All other modifications | 6.64 lbf⋅ft |
First stage | 59 lbf⋅ft |
Use new screw. | |
Second stage | 90° |
First stage | 14.75 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
All Audi diesel V6 2.7 L CGKA engines | 8.85 lbf⋅ft |
All Audi diesel V6 2.7 L CGKB engines | 8.85 lbf⋅ft |
All Audi diesel V6 3.0 L CLAB engines | 16.96 lbf⋅ft |
First stage | 3.69 lbf⋅ft |
Third stage | 6.64 lbf⋅ft |
Second stage | 6.64 lbf⋅ft |
Tighten cross-wise. |
Fourth stage | 14.75 lbf⋅ft |
Fifth stage | 11.8 lbf⋅ft |
First stage | 6.64 lbf⋅ft |
Second stage | 2.21 lbf⋅ft |
Replace screws. | |
Third stage | 2.21 lbf⋅ft |
Control tensioner | |
Fifth stage | 90° |
Fourth stage | 5.9 lbf⋅ft |
First stage | 3.69 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 5.9 lbf⋅ft |
Replace bolts and tighten crosswise. | |
Second stage | 90° |
First stage | 3.69 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 5.9 lbf⋅ft |
Replace bolts and tighten crosswise. | |
Second stage | 90° |
Toothed belt guard | 7.38 lbf⋅ft |
All Audi diesel straight-4 2.0 L CNHA engines | 8.85 lbf⋅ft |
All other modifications | 7.38 lbf⋅ft |
2.0 TDI with diesel straight-4 2.0 L 188 HP engine (2013.9–) | 8.85 lbf⋅ft |
Toothed belt guard center | 7.38 lbf⋅ft |
Central screws | 16.96 lbf⋅ft |
First stage | 14.75 lbf⋅ft |
Second stage | 45° |
Central screws | 16.96 lbf⋅ft |
First stage | 14.75 lbf⋅ft |
Replace nuts. | |
Second stage | 45° |
Stud screws | 11.06 lbf⋅ft |
Replace the stud bolt. |
First stage | 14.75 lbf⋅ft |
Replace nuts. | |
Second stage | 45° |
First stage | 3.69 lbf⋅ft |
Replace bolts. | |
Second stage | 90° |
First stage | 3.69 lbf⋅ft |
Replace bolts. | |
Second stage | 5.9 lbf⋅ft |
Tighten cross-wise. | |
Third stage | 90° |
All other modifications | 6.64 lbf⋅ft |
Tighten cross-wise. |
First stage | 5.9 lbf⋅ft |
Second stage | 45° |
Heat-exchanger on oil filter housing | 16.96 lbf⋅ft |
All Audi diesel straight-4 2.0 L CAHA engines | 18.44 lbf⋅ft |
All Audi diesel straight-4 2.0 L CAHB engines | 18.44 lbf⋅ft |
All Audi gasoline V6 3.2 L CALA engines | 6.64 lbf⋅ft |
All Audi diesel V6 2.7 L CGKA engines | 6.64 lbf⋅ft |
All Audi diesel V6 2.7 L CGKB engines | 6.64 lbf⋅ft |
All Audi diesel straight-4 2.0 L CGLC engines | 8.11 lbf⋅ft |
All Audi diesel straight-4 2.0 L CGLD engines | 18.44 lbf⋅ft |
CAGA engine | 18.44 lbf⋅ft |
CJCA engine | 8.11 lbf⋅ft |
All Audi diesel straight-4 2.0 L CJCD engines | 8.11 lbf⋅ft |
All Audi diesel V6 3.0 L CLAB engines | 6.64 lbf⋅ft |
First stage | 5.9 lbf⋅ft |
Replace screws. | |
Second stage | 45° |
All Audi diesel straight-4 2.0 L CNHA engines | Component must not be knocked down. |
All other modifications | 16.96 lbf⋅ft |
Plastic oil sump | Tighten screw up to the stop. |
Replace sealing rings. | |
Sheet-steel sump | 22.13 lbf⋅ft |
Replace sealing rings. |
All other modifications | 22.13 lbf⋅ft |
Replace sealing rings. |
All Audi gasoline straight-4 2.0 L CAED engines | 16.23 lbf⋅ft |
Oil filter cover | 18.44 lbf⋅ft |
Slightly oil sealing lips. |
Oil filter cover | 18.44 lbf⋅ft |
Oil filter cover | 18.44 lbf⋅ft |
First stage | Tighten by hand |
Use new screws and tighten them crosswise. | |
Second stage | 14.75 lbf⋅ft |
Third stage | 90° |
Cap | 18.44 lbf⋅ft |
First stage | 11.06 lbf⋅ft |
Tighten alternately starting from the top left | |
Second stage | 90° |
Replace screws. |
Oil filter cover | 18.44 lbf⋅ft |
First stage | 11.06 lbf⋅ft |
Tighten alternately starting from the top left | |
Second stage | 90° |
Oil filter cover | 18.44 lbf⋅ft |
On the engine block | 9.59 lbf⋅ft |
Cap | 25.81 lbf⋅ft |
Otherwise | 6.64 lbf⋅ft |
Oil filter cover | 18.44 lbf⋅ft |
First stage | 10.33 lbf⋅ft |
Tighten alternately starting from the top left | |
Second stage | 90° |
First stage | 11.06 lbf⋅ft |
Use new screws and tighten them crosswise. | |
Second stage | 90° |
First stage | 10.33 lbf⋅ft |
Use new screws and tighten them crosswise. | |
Second stage | 90° |
Oil filter cover | 18.44 lbf⋅ft |
First stage | 10.33 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Oil filter cover | 25.81 lbf⋅ft |
On the engine block | 6.64 lbf⋅ft |
First stage | Screw in screws by hand. |
Use new screws and tighten them crosswise. | |
Second stage | 14.75 lbf⋅ft |
Third stage | 90° |
First stage | 14.75 lbf⋅ft |
Use new screws and tighten them crosswise. | |
Second stage | 90° |
Oil pressure sensor | 14.75 lbf⋅ft |
First stage | 5.9 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
All Audi diesel straight-4 2.0 L CJCD engines | 6.64 lbf⋅ft |
First stage | 5.9 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 8.85 lbf⋅ft |
Replace screws. | |
Second stage | 180° |
All other modifications | 14.75 lbf⋅ft |
First stage | 22.13 lbf⋅ft |
Use new screw. | |
Second stage | 90° |
All Audi diesel V6 2.7 L CGKA engines | 47.2 lbf⋅ft |
All Audi diesel V6 2.7 L CGKB engines | 47.2 lbf⋅ft |
First stage | 22.13 lbf⋅ft |
Replace screws. | |
Second stage | 45° |
First stage | 5.9 lbf⋅ft |
Replace screws. |
Second stage | 180° |
Third stage | 45° |
Fourth stage | 180° |
Fifth stage | 90° |
First stage | 5.9 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 5.9 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 11.06 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
M10 | 29.5 lbf⋅ft |
M7 | 11.06 lbf⋅ft |
Gradually tighten screws crosswise. |
First stage | 3.69 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 3.69 lbf⋅ft |
Tighten cross-wise. | |
Second stage | 11.8 lbf⋅ft |
First stage | 5.9 lbf⋅ft |
Use new screws and tighten them crosswise. | |
Second stage | 45° |
First stage | 11.06 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 11.06 lbf⋅ft |
Replace screws. | |
Second stage | 105° |
First stage | 3.69 lbf⋅ft |
Tighten the screws crosswise. | |
Second stage | 5.9 lbf⋅ft |
Replace screws. | |
Third stage | 90° |
First stage | 3.69 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Locking screws | 18.44 lbf⋅ft |
TDC marking. |
First stage | 3.69 lbf⋅ft |
Tighten cross-wise. | |
Second stage | 11.06 lbf⋅ft |
M10 | 29.5 lbf⋅ft |
M7 | 11.06 lbf⋅ft |
Gradually tighten screws crosswise. |
First stage | 11.06 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
M10 | 29.5 lbf⋅ft |
M7 | 11.06 lbf⋅ft |
Gradually tighten screws crosswise. |
First stage | 3.69 lbf⋅ft |
tighten gradually cross-wise |
Second stage | 11.06 lbf⋅ft |
Third stage | 90° |
Fourth stage | 9.59 lbf⋅ft |
tighten gradually cross-wise |
Fifth stage | 16.96 lbf⋅ft |
First stage | 11.06 lbf⋅ft |
Replace screws. | |
Second stage | 105° |
First stage | 3.69 lbf⋅ft |
Tighten the screws crosswise. | |
Second stage | 5.9 lbf⋅ft |
Replace screws. | |
Third stage | 90° |
First stage | 3.69 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Locking screws | 18.44 lbf⋅ft |
TDC marking. |
First stage | 3.69 lbf⋅ft |
Tighten cross-wise. | |
Second stage | 11.06 lbf⋅ft |
First stage | 5.9 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 5.9 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 5.9 lbf⋅ft |
Replace screws. |
Second stage | 180° |
Third stage | 45° |
Fourth stage | 180° |
Fifth stage | 90° |
First stage | 3.69 lbf⋅ft |
Second stage | 9.59 lbf⋅ft |
Third stage | 29.5 lbf⋅ft |
First stage | 5.9 lbf⋅ft |
Replace screws. | |
Second stage | 45° |
First stage | 11.06 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Camshaft sensor | 7.38 lbf⋅ft |
All Audi diesel straight-4 2.0 L CNHA engines | 5.9 lbf⋅ft |
All other modifications | 3.69 lbf⋅ft |
All Audi gasoline straight-4 1.8 L CABD engines | 7.38 lbf⋅ft |
All Audi gasoline V6 3.2 L CALA engines | 6.64 lbf⋅ft |
All Audi gasoline straight-4 1.8 L CDHB engines | 2.95 lbf⋅ft |
All Audi diesel V6 2.7 L CGKA engines | 6.64 lbf⋅ft |
All Audi diesel V6 2.7 L CGKB engines | 6.64 lbf⋅ft |
All Audi diesel straight-4 2.0 L CJCA engines | 2.95 lbf⋅ft |
All Audi gasoline straight-4 1.8 L CJEB engines | 7.38 lbf⋅ft |
All Audi diesel V6 3.0 L CLAB engines | 6.64 lbf⋅ft |
All Audi gasoline straight-4 2.0 L CNCD engines | 6.64 lbf⋅ft |
All other modifications | 3.32 lbf⋅ft |
At the turbocharger | 33.19 lbf⋅ft |
On particle filter | 44.25 lbf⋅ft |
On exhaust manifold | 33.19 lbf⋅ft |
On particle filter | 44.25 lbf⋅ft |
With combustion chamber pressure sensor | 8.85 lbf⋅ft |
Without combustion chamber pressure sensor | 12.54 lbf⋅ft |
All other modifications | 12.54 lbf⋅ft |
First stage | 5.9 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
All other modifications | 14.75 lbf⋅ft |
All Audi diesel straight-4 2.0 L CAHA engines | 36.88 lbf⋅ft |
All Audi diesel straight-4 2.0 L CAHB engines | 36.88 lbf⋅ft |
All Audi diesel V6 2.7 L CGKA engines | 36.88 lbf⋅ft |
All Audi diesel V6 2.7 L CGKB engines | 36.88 lbf⋅ft |
All Audi diesel straight-4 2.0 L CGLD engines | 36.88 lbf⋅ft |
All Audi gasoline straight-4 2.0 L CNCD engines | 44.25 lbf⋅ft |
All other modifications | 40.57 lbf⋅ft |
2.0 TDI with diesel straight-4 2.0 L 188 HP engine (2013.9–) | 40.57 lbf⋅ft |
On the engine block | 29.5 lbf⋅ft |
At the subframe | 40.57 lbf⋅ft |
First stage | 66.38 lbf⋅ft |
Use new screw. | |
Second stage | 90° |
At the subframe | 40.57 lbf⋅ft |
First stage | 66.38 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 84.82 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 84.82 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 84.82 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
First stage | 36.88 lbf⋅ft |
Use new screws. | |
Second stage | 90° |
First stage | 66.38 lbf⋅ft |
Use new screws. | |
Second stage | 135° |
First stage | 66.38 lbf⋅ft |
Use new screws. | |
Second stage | 90° |
First stage | 66.38 lbf⋅ft |
Use new screw. | |
Second stage | 90° |
With electric servo-steering | 66.38 lbf⋅ft |
Use new screw. | |
With hydraulic servo-steering | 66.38 lbf⋅ft |
Use new screw. |
With electric servo-steering | 90° |
With hydraulic servo-steering | 135° |
At the subframe | 40.57 lbf⋅ft |
On engine | 29.5 lbf⋅ft |
Cross support | 29.5 lbf⋅ft |
On the engine block | 18.44 lbf⋅ft |
Torque support bracket | 18.44 lbf⋅ft |
All Audi gasoline V6 3.2 L CALA engines | 16.96 lbf⋅ft |
Replace nut. | |
All Audi diesel V6 2.7 L CGKA engines | 16.96 lbf⋅ft |
Replace the nuts and use fitting paste | |
All Audi diesel V6 2.7 L CGKB engines | 16.96 lbf⋅ft |
Replace the nuts and use fitting paste | |
All Audi diesel straight-4 2.0 L CJCA engines | 16.96 lbf⋅ft |
Replace the nuts and use fitting paste | |
All other modifications | 29.5 lbf⋅ft |
Replace the nuts and use fitting paste |
Catalytic converter bracket | 16.96 lbf⋅ft |
All Audi diesel V6 2.7 L CGKA engines | 16.96 lbf⋅ft |
All Audi diesel straight-4 2.0 L CJCD engines | 16.96 lbf⋅ft |
Replace nuts. Use hot screw paste. |
First stage | 1.48 lbf⋅ft |
Second stage | 5.16 lbf⋅ft |
2.0 TDI with diesel straight-4 2.0 L 188 HP engine (2013.9–) | 33.19 lbf⋅ft |
Bottom | 22.13 lbf⋅ft |
Replace nuts. Use hot screw paste. |
First stage | 3.69 lbf⋅ft |
Replace nuts. Use hot screw paste. | |
Second stage | 8.85 lbf⋅ft |
Third stage | 11.8 lbf⋅ft |
Fourth stage | 18.44 lbf⋅ft |
First stage | 11.06 lbf⋅ft |
Replace nuts. | |
Second stage | 18.44 lbf⋅ft |
Bottom | 22.13 lbf⋅ft |
Replace nuts. |
First stage | 3.69 lbf⋅ft |
Replace nuts. | |
Second stage | 8.85 lbf⋅ft |
Tighten cross-wise. | |
Third stage | 11.8 lbf⋅ft |
Fourth stage | 18.44 lbf⋅ft |
Bottom | 22.13 lbf⋅ft |
Replace the nuts and use fitting paste |
First stage | 3.69 lbf⋅ft |
Replace nuts. | |
Second stage | 8.85 lbf⋅ft |
Third stage | 11.8 lbf⋅ft |
Fourth stage | 18.44 lbf⋅ft |
At the cylinder head | 18.44 lbf⋅ft |
Replace nuts. Use hot screw paste. |
First stage | 22.13 lbf⋅ft |
Replace screws. Use hot screw paste. | |
Second stage | 90° |
First stage | 8.11 lbf⋅ft |
Tighten screws from the inside outwards. | |
Second stage | 16.23 lbf⋅ft |
Third stage | 16.23 lbf⋅ft |
Control tensioner |
All other modifications | 18.44 lbf⋅ft |
Replace the nuts and use fitting paste |
All Audi diesel straight-4 2.0 L CJCD engines | 18.44 lbf⋅ft |
All Audi diesel straight-4 2.0 L CNHA engines | 7.38 lbf⋅ft |
First stage | 22.13 lbf⋅ft |
Replace screws and nuts. | |
Second stage | 90° |
Clamps | 18.44 lbf⋅ft |
Replace nuts. |
All other modifications | 18.44 lbf⋅ft |
Replace nuts. |
Exhaust pipe bracket | 16.96 lbf⋅ft |
All Audi gasoline straight-4 2.0 L CAED engines | 18.44 lbf⋅ft |
All Audi diesel straight-4 2.0 L CJCD engines | 16.96 lbf⋅ft |
Clamps | 16.96 lbf⋅ft |
All Audi diesel straight-4 2.0 L CNHA engines | 16.96 lbf⋅ft |
First stage | 1.48 lbf⋅ft |
Second stage | 90° |
slacken | |
Third stage | 14.75 lbf⋅ft |
2.0 TDI with diesel straight-4 2.0 L 188 HP engine (2013.9–) | 16.96 lbf⋅ft |
Replace nuts. |
Fuel filter bracket | 5.9 lbf⋅ft |
Union nuts | 14.75 lbf⋅ft |
Union nuts | 19.91 lbf⋅ft |
Preliminary feed pump | 5.9 lbf⋅ft |
Spark plugs | 22.13 lbf⋅ft |
M10 × 50 screws | 47.94 lbf⋅ft |
M10 | 47.94 lbf⋅ft |
First stage | 22.13 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
M10 | 47.94 lbf⋅ft |
First stage | 22.13 lbf⋅ft |
Second stage | 90° |
M10 | 47.94 lbf⋅ft |
First stage | 22.13 lbf⋅ft |
Second stage | 90° |
M10 × 50 screws | 47.94 lbf⋅ft |
M10 | 47.94 lbf⋅ft |
Property class 10.9 |
First stage | 22.13 lbf⋅ft |
Replace screws. | |
Second stage | 90° |
Please be noted that all capacities listed here are approximate. Check fluid levels when adding or refilling as recommended in your 2013 Audi A5 Cabriolet user's manual. Keep in mind that all information here is provided “as is” without any warranty of any kind.
Before doing any DIY service please check your insurance policy and Audi warranty policy for your region. In some regions DIY service may invalidate your warranty.
Table of Contents
- Air Conditioning Compressor Oil Capacity
- Air Conditioning Refrigerant Capacity
- Automatic Transmission Fluid Capacity
- Axle Oil Capacity
- Brake Fluid Capacity
- Cooling Fluid Capacity
- Engine Oil Capacity
- Fluid and Lubricant Specifications
- Manual Transmission Oil Capacity
- Brake System Specifications
- Chassis Specifications
- Cooling System Specifications
- Drive Belts Specifications
- Electrical System Specifications
- Emission
- Engine Fastener Tightening Specifications
- Front Suspension Fastener Tightening Specifications
- Rear Suspension Fastener Tightening Specifications
- Transmission Fastener Tightening Specifications
Conquer your fears and never give up!
DIY car service is not as difficult as it looks like and it might save you thousands of dollars per year. It might be even fun and a good thing to do with your kids on a weekend to teach them how basic machinery works. It's really hard to screw something up and damage your car permanently if you use right tools, follow Audi A5 Cabriolet service manual and use right parts and fluids in prescribed amounts. Even modern cars stuffed with electronics can be serviced in your garage or even in your driveway. Changing engine oil, brake fluid, ATF, replacing brake pads, and etc. It's all may be done by yourself in a mater of a couple of hours.
Doing basic service for your 2013 Audi A5 Cabriolet you're not only saving money, but also also improving your technical skills and learning something new.